Letter G Linocut Design – Second Colour Printed

I have joined a linocut group on facebook, where members can sign up to print a linocut letter for different themed alphabets. I have chosen the letter ‘G’ for a freestyle alphabet, image size 15×15 cm. You can read more about how I came up with my design here. And about printing the first colour here.

Letter G linocut first colour printed © Catherine Cronin

Letter G linocut first colour printed

I am doing a reduction linocut of three colours; below is an image of the ‘soft-cut’ block cut for the second colour to be printed. Only the letter ‘G’ will be printed; I left some ‘triangular’ shapes near the edge to give a bit of stability to the block.

2ndColourBlockGLinocutweb

I am using Caligo waterbased inks; the first colour I mixed was taupe (yellowish light grey), this second colour is straight from the tube, Naphthol red.

NaphtholRedInkRolledweb

2ndColourBlockGLinocuInkedweb

I was worried that my registration method for printing the block in the same position in relation to the paper would not be accurate enough. There has been some slight movement on some of the prints but it is pretty spot on. Image below shows the block inked in register on an acetate sheet, the printing paper is lined up with the black horizontal and vertical lines towards the bottom and right. I have used cut paper to mask off areas of the block that have picked up ink in the lower level which I don’t want to print.

2ndColourBlockGLinocutRegisteredweb

 

Here are the prints drying, so far so good; I have one final colour to print which is black, hopefully the registration will be okay for the last colour too – fingers crossed!

2ndColourBlockGLinocutPrintedDryingweb

(© Catherine Cronin)

 

Letter G Linocut Design – First Colour Printed

I have joined a linocut group on facebook, where members can sign up to print a linocut letter for different themed alphabets. I have chosen the letter ‘G’ for a freestyle alphabet, image size 15×15 cm. You can read more about how I came up with my design here.

FINAL DESIGN

FINAL DESIGN

I am doing a reduction linocut, also known as a ‘suicide’ cut. Once the first colour is printed you remove more lino from the block to print the next colour and so on for each subsequent colour. This means that if you make a mistake you cannot start again. There is no going back with a ‘suicide’ cut.

LetterG_marked_linoWeb

 

LetterG_marked_lino2Web

 

I marked out the image on my ‘soft cut’ lino using biro; making sure that my letter ‘G’ was drawn as a mirror image so that when I take a print, the print will show the letter ‘G’ the correct way around.The O and X marks denote areas of colour. Where there are no O and X marks that is the material I want to remove first.

LetterG_marked_lino_FirstCutweb

 

I mixed the first colour which is taupe (a yellowish light grey) using Caligo waterbased inks. I wanted a warmer grey than the graphite pencil as seen in my sketched final design.

I found out that if I didn’t roll on the ink to completely cover the biro pen markings on the lino block, the biro pen actually started to print onto the paper – that was an unwelcome surprise.

LetterG_CaligoInksFirstColourweb LetterG_rollingInkFirstColourweb

LetterG_InkingFirstColourweb

LetterG_FirstBlock_taupeweb

FIRST COLOUR PRINTED

 

I regret the registration method I used to make sure that my lino block and paper could be printed in the same position for each colour. I marked out my lino block in relation to the position of the paper with marker pen on acetate. This method works, but it is not 100% accurate, there is a slight movement of position each time you line up your block and paper. As my image depends on the geometry of the design I should have used a more accurate registration method; I realised this too late! I will have to press on and hope that any movement is very slight and not too noticeable when it comes to printing the next two colours.

(© Catherine Cronin)

 

Letter G Linocut Design

I have joined a linocut group on facebook, where members can sign up to print a linocut letter for different themed alphabets. I have chosen the letter ‘G’ for a freestyle alphabet, image size 15×15 cm. The deadline for the final image is the end of January. Here is an insight into how I came up with my final design: as a starting point I already had the idea that it would be be a graphic image made up of coloured triangles where the letter would be part of the background pattern but at the same time different enough to ‘read’ as a letter; I also limited myself to 3 colours as I don’t have much time to execute the print before the deadline. It is interesting to see that the second design settled the form and colour of the letter, but it took another three designs to settle on the background and a realisation that for clarity the letter had to be very different to the patterned background. The letter only shares the triangle form with the background. I really like this image and I might carry on with a whole alphabet in this style.

First Design

First Design

 

Second Design

Second Design

 

Third Design

Third Design

 

Fourt Design

Fourth Design

 

FINAL DESIGN

FINAL DESIGN

(© Catherine Cronin)

Weekly Sketch – Physalis – 17/10/2015

I love Physalis; such pleasure to open the papery lantern shaped husks, revealing a bright orange sun bursting with juice and sweetness. I like the very quick pencil sketch I made of this fruit below. A coloured image grew in my mind that would showcase the brightest orange of this fruit, however my attempt in watercolour and oil pastel was not a success. But mistakes and failures are the steps that have to be taken towards resolving an image. More work to be done here.

PhysalisSketch_web

Physalis_web

 

(© Catherine Cronin)